CRYSTAL QUEST® Commercial and Industrial Arsenic water Filters
The previous arsenic standard of 50 parts per billion (ppb) was originally set by the EPA in 1975, based on a Public Health Service standard originally established in 1942. In the mid-1990s, the medical community began to question the health and safety effects of an arsenic limit of 50 ppb. The World Health Organization had set their arsenic limit at 10 ppb which was one of the only contaminate limits that was lower than the U.S. EPA’s standard. In March of 1999, the National Academy of Sciences released a report concluding that “the current standard does not achieve EPA's goal of protecting public health and should be lowered as soon as possible.” The report was based on extensive clinical studies in  Germany, Japan, Taiwan, Bangladesh, Argentina, Mexico, and Chile.

The EPA considered lowering the arsenic limit from 50 ppb to as low as 3 ppb. The new arsenic limit was released at 10 ppb in January of 2001, and was one of the last official acts of the Clinton Administration. In March of 2001, the Bush Administration suspended the new arsenic rule pending further consideration. The Bush administration felt that additional scientific data was needed to justify the large cost of compliance. While the rule was under further consideration, more health effects data was compiled, which suggested that the 10 ppb limit for arsenic may not be strict enough. In October of 2001, the rule was released at 10 ppb which is the current level for the arsenic contaminant.

THE ORIGIN OF ARSENIC
Arsenic is an element that occurs in the earth's crust. Accordingly, there are natural sources of exposure. These include weathering of rocks and erosion depositing arsenic in water bodies and uptake of the metal by animals and plants. Consumption of food and water are the major sources of arsenic exposure for the majority of the population. People may also be exposed from industrial sources, since arsenic is used in semi-conductor manufacturing, petroleum refining, wood preservatives, animal feed additives, and herbicides.

MAXIMUM CONTAMINANT LEVEL
The EPA established a maximum contaminant level for arsenic, 50 micrograms per liter (50 uq/L) or parts per billion (ppb) in 1976. In October of 2001, the MCL was lowered to 10 ppb.

PUBLIC HEALTH CONCERNS
Arsenic can combine with other elements to form inorganic and organic arsenicals.  In general, inorganic derivatives are regarded as more toxic than the organic forms. While food contains both inorganic and organic arsenicals, mainly inorganic forms are present in water. Exposure to arsenic at high levels poses serious health effects, since it is a known human carcinogen. In addition, it has been reported to affect the vascular system in humans and has been associated with the development of diabetes. Arsenic is poisonous in doses significantly larger than 65 mg (1 grain), and the poisoning can arise from a single large dose, or from repeated small doses, as, for example, inhalation of arsenical gases or dust.

 
  • Utilizes a strongly basic hybrid anion exchange resin specially formulated to selectively remove arsenic.
  • Exhibits extraordinary throughput capacity in arsenic removal service on potable water supplies. Its performance is virtually unaffected by common anions, such as chlorides, bicarbonates or sulfates. It is effective over the entire pH range of potable water.
  • Made from NSF/ANSI-61 validated anion exchange resin
  • No arsenic dumping - effluent arsenic levels will not exceed influent levels if resin is operated past exhaustion point
  • Filtration capacity: Up to 500,000 gallons per Cu. Ft. Resin (at 50 ppb in influent with 10 ppb in effluent)
STANDARD FEATURES
  • Metered Fleck® controls
  • Heavy duty Structural® tanks Poly Glass™ mineral tank
  • All brass, motor driven control valve with fully adjustable regeneration cycles
  • Self-adjusting backwash controller
  • Flow controller to limit backwash flow
  • Engineered for commercial & industrial use
  • Optional skid mounting for tank

 
   
Capacity (Gallons) at 50 ppb in influent with 10 ppb in effluent
 1,500,000 2,000,000 3,500,000 5,000,000 7,500,000 10,000,000 15,000,000 20,000,000
Model
CQE-CO-02067
 CQE-CO-02068 CQE-CO-02069 CQE-CO-02070 CQE-CO-02071 CQE-CO-02072 CQE-CO-02073 CQE-CO-02074
Fleck Valve 2850 2900 2900 2900 3900 3900 3900 3900
Type Single Single Single Single Single Single Single Single
Pipe Size 1.5" 2" 2" 2" 3" 3" 3" 3"
Cu. Ft. Resin 3 4 7 10 15 20 30 40
Mineral Tank Size, in. 14x65 16x65 21x62 24x72 30x72 36x72 42x72 48x72
Service Flow, GPM 15 20 67 67 158 185 200 220
Peak Flow, GPM 30 40 85 85 212 250 268 288
Backwash Flow, GPM 6 8 15 20 30 40 60 80
Space Required, in. (WxDxH) 15x16x75 17x18x75 23x24x84 24x24x95 32x32x95 40x48x95 46x54x95 52x60x95
Shipping Weight, lbs. 194 260 410 800 990 1,200 1,930 2,650

Price

 $4204 $4904 $7004 $9204 $17304 $20604 $28674 $34264
 
For  your specific needs of custom-made water treatment contact us at commercial@crystalquest.com
Fleck 2850 Valve* Fleck 2900 Valve* Fleck 3900 Valve*
     * “All valves are timer valves”.
  • Design and specifications are subject to change without notice.

.